Project 300L Index Page

Impressions after 120 miles

• Light weight
• Adequate power
• Proper screen
• Returned to stock gearing (now ticks over @ 4mph in 1st)
• Rally Raid suspension
• Tall bars and other functional accessories fitted by seller
• Mpg

• Thinned out seat
• Swingarm chain alignment marks
• Annoying white rpm warning light
• Mitas trials tyres on the road
• Pathetic tool kit
• Tiny tank
• Vulnerable radiators

After replacing the front sprocket with the stock 14T and leaving the oversized rear for later, I set off for a 100-mile ride to Dorset. Had I looked properly I’d have realised the rear was actually a massive 45T not 42, as the seller claimed. Stock is 40T so that explained why I seemed to be belting along at 70mph+ along the A3 and M27, but cars were still passing me stuck in the slow lane.

The 300L is so light it initially feels skittish; I wouldn’t fancy it in strong crosswinds. But the proper screen (and my Mosko jacket) helped hold back some heavy showers and the thinned-down seat (from Peak?) had just about 100 miles of padding left in it.
Talking of seat comfort and convenience, I reflexively removed the 1970s relic seat strap. Did Soichiro Honda impose some edict that they shall be fitted to trail bikes in perpetuity? The other thing I did was saw open the rear seat bracket so that removing the seat means just loosening the two frame/rack bolts either side, not removing them altogether with washers and spacers tumbling into the gravel.
Fyi my lowered seat height with the stock rear IRC tyre refitted is 34.5″ or 87.6cm which is nearly an inch lower than Honda’s specs at 880cm.

I’d never heard off the annoying white light in the console which starts flashing ever faster as you pass 7000rpm. The red line is another 3500rpm away, so what’s the point of it? To warn you to change gear or you’re going too fast? Whatever, it seems it can be adjusted up the rev scale and out of the way (left).

I’m not so keen on the ET 01 and 05 Mitas trials tyres either. The seller fitted them for the LET. I’m sure once aired down the grip is amazing in UK mud, but the soft, square knobs squidge about at fast road speeds.

With the gearing still lower than stock, I have to assume that the speedo was over-reading even more than normal, but on the open road it did feel like the L held up well against what I recall of my Himalayan, and is definitely much better at speed than my WR250 with similar power and weight. And, contrary to my impression of riding a near-new 300 Rally last year, there’s definitely a tad more poke than my old 250L. A few 300L owners have told me the bike loosens up substantially once past 1000 miles, which I did somewhere around Southampton.

Arriving with one bar on the fuel gauge, I filled up in Dorset with 5.7 litres at 110 miles on the odo. That means there was over 2 litres or 40+ miles in the tank which seems unlikely over that distance. An average of 90mpg was shown on the console but I think the gearing may have messed with the odo reading. We shall see.

A couple of days later I refitted the stock 40T rear sprocket and IRC rear tyre. With a thick Michelin tube, the 4.00×18 Mitas weighed 6.9kg, while the IRC and a cheap tube were only 6kg – not a huge difference. And amazingly, both tyres and tubes were heavier than the back wheel, now at 5.3kg with a 40T sprocket.
The near-new Regina chain fitted for the seller’s very low 13/45 gearing was now a link too long and I’d left my chain breaker in London (I knew this would happen…). The OEM chain supplied loose was missing the joining link, plus I’m not sure I want to bother with it, even as a burner. I soon learned that you can’t bash out chain pins with a hammer and punch like you can on a pushbike; some serious force is needed, or YouTube suggested grinding off the end of the pin then prising the plate off. I don’t have a grinder either and a hacksaw didn’t work but luckily the Gear Box Bike Shop in nearby Poole was open on coronation Sunday and zipped off a link for a fiver.

While readjusting the cleaned-up chain, I took a moment to lament the passing of footproof snail cam adjusters, I bet there’s a way of retro fitting them to fiddly lock-nut adjusters. And is it me, or is the swingarm alignment marker maddeningly on the wrong, underside of the axle? I can’t bend like I used to could so had to lie flat on the ground, which means getting all the way up again. One… two… three… Ooof!

I checked the spring rate on the Rally Raid Stage 1 shock. On top of the spring was marked a surprising and reassuringly firm 100nm which is what it feels like. No wonder the seller found the 300 a bit tippy and decided to sell. I’m tempted to splash out another 200 quid on an HPA (above right) which seems to be a special order from Rally Raid, but am told it may need a change of spring. We shall see.

The bike’s tool kit sits in a space-wasting plastic box. I’m sure someone could fabricate a more functional replacement or even a 2-litre fuel cell in its place. Once opened I’m even more disappointed than expected: a single fat 14/17 open spanner and a pair of allens, enough to remove the mirrors, seat and side panels. Rally Raid make a nifty combo wrench (left) which does both wheels for under 30 quid, but it’s not in stock. Once I have that alongside my trusty Motion Pro Trail Toolkit with an added 8mm socket and a couple of allens I’ll be good to go.

Now back on stock gearing and rear tyre, I set off across the Dorset heathland to verify the odo against a GPS, while assuming the speedo will indicate the usual mandated 8% over. Speedo accuracy isn’t so important to me, but on a travel bike you want to trust the bike’s odo which are somehow engineeringly unlinked to the exaggerated speedo reading and often manage to be nearly spot on. Result: over 10 GPS miles the 300’s odo indicated 10.15, so odo is 1.5% over. I can live with that.
Also, riding along at tickover in first, the speedo indicated 3-4mph which is about as slow as I can balance sat down, and just as it should be for low speed control for do-it-all trail biking. I really wonder why the seller lowered the gearing so much – he rode the Lands End Trial, not the SSDT. I remember my XT660Z did an annoying 8mph at tickover as do many bikes. Way too high for tricking along or not fragging the clutch on walking-pace climbs. As I mentioned in my quick ride on a 300 Rally last year, the 300s do seem to have ‘Goldilocks’ gearing: low 1st matched with an overdrive 6th.
Other good things I noted. Even though the seller was shorter than me, the Renthal bars he fitted are, for once, just right for me when standing. They don’t look that tall so I think this must be innate to the bike’s design. What a relief not to get bogged down in the usual risers and re-routed cables, even if I might have prefered brace-free FatBar.

Out of interest and with the luxury of a flat, garage floor for the first time in my biking life, I decided to do the bathroom scales trick and weigh the bike, one wheel at a time. Result: with an added rack, bashplate, screen, frame protectors, Rally Raid suspension, barks, tail tidy, and a full tank (‘kerb weight’), my 300L weighed in at 146kg. It feels like it too and if you deduct say, 4 kilos for the listed accessories (some of which – bars, shock tail tidy – save weight over stock), that matches up well with Honda’s 142kg kerb weight claim. Next jobs: get that weight up!

• Acerbis 14-litre tank
• Chinese radiator crash bars
• USB power take-off
• Cool Cover
• Refit front OEM tyre
ª Go somewhere good